allowable deviation
英 [əˈlaʊəbl ˌdiːviˈeɪʃn]
美 [əˈlaʊəbl ˌdiːviˈeɪʃn]
网络 许用偏差; 允许偏差; 容许偏差,许用偏差; 容许偏差
双语例句
- Bolt Hole Spacing should be consistent with the allowable deviation of norms.
螺栓孔孔距的允许偏差应符合规范的规定。 - What is the allowable deviation from straightness for a40 foot long primary truss member?
对40英寸长的主珩架构件允许的直线度偏差是多少？ - Respectively using magnesium oxide and bone ash cupels, the result deviation of gold content in the samples is within the allowable deviation of the national standards.
分别使用镁砂灰皿和骨灰灰皿，样品含Au量的分析结果与理论含Au量的偏差均在国家标准的允差范围内； - Calculation of allowable deviation angles of wireline in coiling on drum
钢绳进出滚筒允许偏角的计算 - In this paper, 6 typical variation conditions are calculated and analyzed. The maximum allowable deviation range of raceway position is determining as a control value for machining and measuring.
文中对6种典型变化情况进行了计算分析，从中确定滚道位置最大允许偏差范围，作为加工和测量时的控制值。 - An Exploration into the Allowable Deviation Limits on the Placement of Reinforcement in Reinforced Concrete Beams
钢筋混凝土梁钢筋位置允许偏差标准探讨 - In the single-layer coiling system, γ 2>γ 1i; the deviation of the wireline in the multi-layer coiling system is typical bi-directional deviation, and the allowable deviation angle depends on γ 1.
光滚筒单层卷绕系统中，γ2＞γ1，多层卷绕系统钢绳为典型的双向偏斜，其允许偏角取决于γ1。 - The result showed that the missile can be launched even if some testing parameters exceed allowable deviation, if only the system has enough stability margin and no functional problem.
结果表明，在某些测试参数偏差超出允许的条件下，如果系统有足够稳定裕度，只要不是功能性问题，仍可以进行发射。 - In the paper, the evaluation method of allowable deviation of deceleration in brake rig testing are analysed.
本文分析了制动器台试减速度允差评定方法。 - For an allowable excess loss of 0.3 dB, the deviation of the alignment has to be smaller than 1 μ m.
若要求附加损耗小于03dB，对准偏差须小于1μm。 - Evaluation of Deceleration and Determination of Allowable Deviation of Brake Lining's Friction Factor in Brake Dynamometer Testing
制动器台试减速度评定及制动衬片摩擦系数允差的确定 - Result Before calibration, the deviation of the measurement was 80% ( 8/ 10) of the allowable values. After calibration, the deviation was down to 30% ( 3/ 10).
结果校准后偏差超过允许范围的测定参数为30%（3/10），较校准前的偏差超过允许范围测定参数80%（8/10）明显降低。 - Allowable Deviation about Breakwater Cylinder Installation
关于防波堤圆筒安装的允许偏差 - The precision of t-test was manifested through standard deviation calculation and the allowable deviation was determined.
通过标准偏差计算反映该试验方法的精密度，确定允许差。 - Also, the maximum and allowable range of the locomotive barycenter longitudinal deviation is given when the axle load distribution accords with the railway ministry standards.
同时，对轴式为B0-B0的电力机车，给出了当轴重分配达到部颁标准时机车重心纵向偏离所允许的最大范围。